DoorKing Access Control Installation Nationwide

DoorKing Access Control Installation: The Sandy Springs Owner’s Guide

DoorKing access control installation in Sandy Springs typically runs $1,200-$2,800 for a complete keypad or telephone entry system, depending on whether you’re wiring a single-family driveway gate or a multi-tenant commercial entrance. Most residential DoorKing 1802 or 1833 series installs we do in Sandy Springs are completed in one scheduled visit, with the written price agreed before we touch any tools. Homeowners usually figure out something’s wrong when the keypad stops accepting codes, the call button goes silent, or the gate simply sits there ignoring every command on a rainy Tuesday morning.

Call (470) 885-1464

Which DoorKing Models This Applies To

DoorKing has been building access hardware in California since 1948, and the model numbering tells you most of what you need. The 1802 series covers basic standalone keypads for single-family residential gates. The 1833 and 1834 series add telephone entry capability, which is what you’ll find on most Sandy Springs townhome communities along Roswell Road. The 1838 PC Programmable and the newer 1835 wireless models require different mounting footprints and power supplies, so the back-box dimensions matter.

Here’s how to identify yours without guessing. The model number is stamped on a metal label inside the housing, usually visible once you remove the front cover with a Phillips head. The serial number prefix tells us the manufacturing era: pre-2015 units often used the DKPS power supply with a separate 24VAC transformer, while current production integrates switching power supplies that don’t tolerate Georgia’s voltage spikes as gracefully. We stock both OEM DoorKing transformers and aftermarket equivalents rated for 115-125VAC input, which matters because Sandy Springs sits on a Georgia Power grid that runs a little hot in summer afternoons.

We are an independent service provider, not affiliated with DoorKing. We source OEM parts through authorized distribution and also carry quality aftermarket equivalents where the spec matches, particularly on power supplies and relay boards where the original manufacturer has discontinued a specific revision.

Signs Your DoorKing Access Control Installation Is Failing

• Keypad accepts codes but the gate doesn’t move. Usually the output relay has burned contacts. The 1802-010 relay board in pre-2018 units used a 10A SPDT relay that degrades after roughly 8,000 cycles in Georgia’s humidity; we test contact resistance and replace the board if it’s above 2 ohms closed.
• Intermittent operation that gets worse after rain. Water intrusion at the conduit entrance, common on Sandy Springs properties with underground feeds through clay-heavy soil that shifts seasonally. The moisture corrodes the terminal block before it ever reaches the circuit board.
• Display is dim or flickering. The backlight inverter on older 1833 units fails gradually; you’ll notice it first at dusk. We measure draw at the power supply and replace the inverter assembly when it drops below 80% rated output.
• Call button works for some residents but not others. This points to programming memory corruption in the 1834 directory, not a hardware failure. We can reprogram on-site, but we also back up the directory to our job record so a future lightning strike doesn’t erase it again.
• Gate opens on its own, typically between 2 and 4 AM. The timer function has been accidentally enabled or the relay is chattering due to a failing suppression diode. We see this on properties near the Chattahoochee River where voltage fluctuation is more pronounced.

Before

After

Replacement Cost & What’s Included

The range depends on three things: how far we need to trench or run conduit from the access point to the gate operator, whether the existing low-voltage wiring is still within spec (we test resistance and insulation with a Megger before reusing anything), and whether the property needs a separate pedestrian keypad or just the vehicle gate. Every install price is written and handed to you before we pick up a tool, under Haven Standard Clause 1. The 365-Day Done Right Promise covers all work: if the relay chatters, the display flickers, or the directory loses its memory within a year, we fix it at no charge.

DIY or Call Us?

There’s a safe middle ground here. You can check the obvious stuff: verify the breaker hasn’t tripped, confirm the GFCI outlet hasn’t popped, and look for water inside the housing. If you find moisture, leave the cover off and call us; powering up a wet board destroys it.

What you shouldn’t do: work on the 120VAC supply side without proper lockout, attempt to reprogram the directory without a backup, or splice low-voltage wiring with wire nuts and electrical tape. DoorKing systems use supervised loops that detect resistance changes; a sloppy splice reads as a fault and can disable the safety features. The 24VAC output on older units won’t kill you, but the primary side absolutely can. We’ve replaced three homeowner “fixes” this year in Sandy Springs alone, all of which cost more than the original call would have.

Name what you found. Name what it costs. Name what you left behind. That’s how we work every job.

FAQs