Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Norcross, GA
Gate access control repair in Norcross typically costs $280-$650 for keypad or card-reader troubleshooting, and $450-$1,200 for full video-intercom replacement, with most residential calls completed same-day. The city’s concentration of 1980s-1990s HOA subdivisions and Jimmy Carter Boulevard commercial corridors means we see two distinct repair patterns: aging Elite and DoorKing operators failing in gated communities, and heavy-duty slide gates corroding in industrial lots. Call (470) 885-1464 for a written estimate before any work begins.
Why Norcross Homes Are Different
Norcross was built out hard during Gwinnett County’s 1980s-1990s boom, and that timing matters for every service call we take. The ornamental iron swing gates at hundreds of HOA subdivision entrances - places like Forest Vale and the neighborhoods off Spalding Drive - are now 25-40 years old. Many still run original Elite 900 or DoorKing 9000-series operators wired by the original developers, with control boards that manufacturers discontinued years ago.
The humid subtropical climate here accelerates rust on motor housings and gate frames year-round. Underneath, the red Georgia clay swells in wet winters and contracts in summer drought, progressively heaving gate posts out of plumb. That seasonal movement places chronic stress on hinges, rollers, and track alignments that technicians in newer cities simply don’t encounter. Along the I-85 industrial corridor and Jimmy Carter Boulevard, commercial slide gates and roll-up security doors take additional punishment from freight traffic and road salt.
Our Main Norcross Services
Most Norcross calls fall into three categories. Each has its own dedicated page with full pricing and sub-job detail.
Gate Repair in Norcross
We repair sagging swing gates, misaligned slide-gate tracks, broken hinges, and post-heave damage across Norcross’s full housing stock. In the 1990s subdivisions, we regularly reset gates that have shifted on clay-heaved posts; downtown near historic Norcross, we rebuild wood-framed gates that have rotted at the hinge points. Every repair leaves a photographed record under Clause 4 of The Haven Standard. Gate Repair in Norcross
Gate Installation in Norcross
New gate installation in Norcross ranges from ornamental aluminum swing gates for HOA communities to heavy-duty steel slide gates for Jimmy Carter Boulevard commercial properties. We measure, quote in writing, and schedule - no same-day installation, but a firm date and a fixed price before any work starts. Gate Installation in Norcross
Gate Motor & Opener in Norcross
Motor replacement is the most common call we take in Norcross’s older subdivisions, where original DoorKing and Elite operators have outlived their control boards. We service nine automation brands and will repair rather than replace whenever parts are available. Gate Motor & Opener in Norcross
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Before
AfterGate Access Control in Norcross
Access control in Norcross means maintaining entry systems on gates that were installed when dial-up internet was standard equipment. The original keypads, card readers, and phone-entry systems at hundreds of HOA and commercial properties are now obsolete, failing in clusters as moisture corrodes circuit boards and Georgia clay movement fractures conduit runs. We replace these with modern systems that use the existing low-voltage wiring where possible, documenting every wire label and terminal position under The Haven Standard so the next technician - us or anyone else - knows exactly what was done. Gate Access Control
Keypad Entry
Signs you need it
Buttons stick or don’t register, the housing is cracked from freeze-thaw cycles, or the code works intermittently after rain.
What it costs in Norcross
Keypad repair runs $180-$320; full replacement with a weather-rated unit is $280-$450.
How we do it
We test voltage at the keypad, trace the wiring back to the control board, photograph the terminal connections, then install the new unit and program up to 25 user codes before leaving.
Video Intercom
Signs you need it
Screen is blank or flickering, camera image is washed out, audio cuts out, or the call button doesn’t reach the house phone.
What it costs in Norcross
Video intercom repair starts at $320; full system replacement with WiFi-enabled unit runs $650-$1,200.
How we do it
We verify power and data at the gate station, test cable continuity through underground conduit, then mount the new intercom and pair it with the resident’s phone app, leaving a wiring diagram and photo log.
What Gate Access Control Costs in Norcross
| Item | Typical range in Norcross |
|---|---|
| Keypad repair | $180 - $320 |
| Keypad replacement | $280 - $450 |
| Video intercom repair | $320 - $480 |
| Video intercom replacement | $650 - $1,200 |
| Card reader reprogramming | $150 - $250 |
| Phone entry system repair | $280 - $520 |
Can you fix an old DoorKing keypad in Norcross?
We can repair DoorKing keypads if the circuit board is intact and buttons are available, but many 9000-series boards are discontinued; when parts are unavailable, we quote a replacement with a modern equivalent before any work starts. Call (470) 885-1464 for a free evaluation.
Will a new keypad work with my existing gate opener?
Most modern keypads are compatible with standard 24V or 12V gate operators, including Elite and Mighty Mule systems common in Norcross; we verify voltage and relay type during the estimate visit and confirm compatibility in writing.
Gate Parts & Welding in Norcross
Welding and parts replacement in Norcross is shaped by two forces: rust from year-round humidity and post heave from expanding clay soil. The ornamental iron gates at 1990s HOA entrances often show hinge-pin elongation and rail separation that can be welded and reinforced rather than replaced. Commercial slide gates along Jimmy Carter Boulevard and the I-85 corridor take heavier wear, with broken rollers and bent track that we cut out and re-weld on-site. Gate Parts & Welding
Hinge Replacement
Signs you need it
Gate sags and drags, leaves a gap when closed, or the hinge pin wobbles in the barrel.
What it costs in Norcross
Hinge replacement runs $220-$380 for residential swing gates; commercial-grade ball-bearing hinges run $340-$520.
How we do it
We support the gate with a temporary prop, cut the old welds, grind the post clean, then weld new heavy-duty hinges with gusset plates and confirm swing geometry before releasing support.
Custom Welding
Signs you need it
Cracked welds at picket-to-rail joints, separated scrollwork, or a gate frame that has torn at the stress point.
What it costs in Norcross
On-site welding repair starts at $180 for minor cracks; structural frame reinforcement runs $320-$580.
How we do it
We grind the crack to bare metal, preheat the joint with a propane torch, lay a 6011 root pass and 7018 fill, then prime and paint the repair to match the existing finish.
What Gate Parts & Welding Costs in Norcross
| Item | Typical range in Norcross |
|---|---|
| Hinge replacement (residential) | $220 - $380 |
| Hinge replacement (commercial) | $340 - $520 |
| On-site welding repair | $180 - $320 |
| Structural frame welding | $320 - $580 |
| Roller replacement (slide gate) | $280 - $450 |
| Post replacement with concrete | $480 - $850 |
Can you weld aluminum gates in Norcross?
Yes, we TIG-weld aluminum gate frames using 4043 filler rod; we verify the alloy first, as many 1990s ornamental gates in Norcross subdivisions are cast aluminum that requires preheating and specialized technique. Call (470) 885-1464 to schedule an on-site evaluation.
Will welding weaken my gate over time?
Properly executed welding with correct rod selection and post-weld cooling does not weaken the gate; we document the weld type and any heat-affected zones in the photo record so future technicians know the repair history.
Brands We Service in Norcross
We stock parts and service nine automation brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. For Norcross’s concentration of older Elite and DoorKing systems, we carry common failure items - limit switches, capacitors, receiver boards - and can source discontinued components through our commercial supply network when available. Most brand-specific repairs are completed on the first visit. our brands
Pricing for Gate Repair in Norcross, GA
| Service | Typical range in Norcross |
|---|---|
| Keypad repair | $180 - $320 |
| Keypad replacement | $280 - $450 |
| Video intercom repair | $320 - $480 |
| Video intercom replacement | $650 - $1,200 |
| Card reader reprogramming | $150 - $250 |
| Phone entry system repair | $280 - $520 |
| Hinge replacement (residential) | $220 - $380 |
| Hinge replacement (commercial) | $340 - $520 |
| On-site welding repair | $180 - $320 |
| Structural frame welding | $320 - $580 |
| Roller replacement (slide gate) | $280 - $450 |
| Post replacement with concrete | $480 - $850 |
Prices in Norcross run higher when we encounter rust-frozen hardware requiring torch cutting, or when clay-heaved posts have shifted the entire gate geometry and require rehanging rather than simple hinge replacement. The price we write down before work starts is the price on the invoice - no exceptions, under Haven Standard Clause 1.
Neighborhoods We Serve in Norcross
Our crews work across Norcross’s full residential and commercial footprint, from the historic downtown district to the I-85 industrial corridor. Response time is typically under two hours for urgent calls anywhere inside the city limits.
- Forest Vale
- Spalding Drive area subdivisions
- Historic Norcross
- Jimmy Carter Boulevard corridor
- I-85 industrial district
Service Area - Cities Near Norcross
We dispatch from our Atlanta office to Norcross and surrounding communities daily. If you’re just outside the city limits, we also serve Lilburn, GA, Duluth, GA, Stone Mountain, GA, and Alpharetta, GA. The same written-price guarantee and documented photo record apply to every job in every city.
Serving Norcross, GA - Our Local Coverage Area
We’re based in the Norcross area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Norcross
Most repair calls in Norcross are dispatched within 90 minutes during business hours and under two hours for after-hours emergencies. A live person answers the phone 24/7 to schedule and confirm arrival windows.
Most 1980s-1990s subdivisions in Norcross require HOA notification for exterior gate modifications, but simple repairs to existing systems typically do not require pre-approval. We document the pre-repair condition with photos that satisfy most HOA maintenance committees.
Norcross’s 1990s development wave left an unusual concentration of aging Elite and DoorKing operators that fail in clusters, while the Jimmy Carter Boulevard commercial corridor generates heavy-duty slide-gate calls that purely residential neighboring cities rarely see. Our technicians carry parts for both patterns.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Norcross Customers Say
"They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H.